Product Ordering Form
To place your order, call +1.514.354.1376 or download and fill in Order Form:
Order Form (.docx) HRCSA Order Form (pdf)
Once completed, submit your form to: info @ termarust.com
Surface Preparation WJ4 (overcoat) or SP6 (recoat if required).
Testing for Non Visible Contaminatea: 2 types of salt test kits.
Chlor-test (Chlorides only)
CSN Kit (Chlorides, Nitrates, Sulfates)
The HRCSA corrosion mitigation system core products.
TR2100 HRCSA Primer/Topcoat
TR2200HS HRCSA Penetrant/Sealer
TRT01 Thinner
TC7101 or Chlor-rid Salt Remover
TC7101 Soluble Salt Remover / Test Kits
High Pressure Water Cleaning (HPWC)(overcoat), or Abrasive Blast (recoat), both require salt mitigation on flat surfaces and to completely flush all opened crevice corroded or pack rusted joints and connections..
Whether High Pressure Water Cleaning HPWC (overcoat), or Abrasive Blasting (recoat), salt mitigation on the flat surfaces and complete flushing of all opened crevice corroded and pack rust joints and connections is needed to ensure compliance with the HRCSA application specifications.
Allowable Surface Area Contaminants (micrograms per meter2): Chlorides – 3ppm, Sulfates -10 ppm, Nitrates – 10 ppm Test Kits can
Also required for thoroughly flushing salts from connections and pack-rust builds.
Whether High pressure water cleaning (overcoat), or abrasive blast (recoat), salt migitation on the flat surfaces and a thorough flushing of all opened connections is needed to ensure compliance to application specifications.
TC7101 or Chlor*Rid salt remover is proportionally added to your potable wash water [100:1 ratio] to mitigate salts at an approximate consumption rate of 600 ft2 / gallon or 15 m2/ litre.
Click to download Soluble Salt Remover TC7101 additive Safety Data Sheets
TC7101 Product Data Sheet.
Chlor-rid Soluble Salt Remover may be used instead of TC7101. (see Chlor-rid website) These chemicals are required to completely flush salts from crevice corroded and pack rusted joints and connections.
Salt Test Kits
Permissible Non Visible Surface Contaminants ug/cm2 micrograms per meter sq.): minimum level of Chloride NVC3 3 ug/cm2, Sulfate NVS10 10ug/cm2, Nitrate NVN10 10ug/cm2.
Test Kits that can be used to determine acceptable non-visible contaminate levels.
CHLOR*TEST (5 surfaces – chlorides only), CHLOR*TEST CSN SALTS (Chlorides, sulfates, nitrates)
TR2100 HRCSA Self-priming topcoat.
TR2100 HRCSA Primer/Topcoat is a single component, single coat, chemically active coating system which is applied by airless spray, brush, roller or paint mitt.. AVAILABLE IN ANY SPECIFIED COLOUR. ( Federal 595 B&C, RAL Standard and Design, or any customer supplies color standard or sample)
TR2100 HRCSA Primer/Topcoat is a low-surface energy overcoat system (for cleaned, tightly adhered, contaminate free coated or exposed steel substrate) whose Spread Rate is 1018 sq. ft. per U.S. Gal. @ 1 mil DFT || 26.2 sq. m. per litre @ 25 microns DFT – ZERO LOSS FACTOR
To download TR2100 Primer/Topcoat additive click Safety Data Sheets and Technical Data Sheets.
Specified Film Thickness: Overcoating clean, tightly adhered existing paint 5 – 7 mils || 125 – 175 microns DFT (Average 200 sq. ft per US gallon ZERO LOSS FACTOR.)
Recoat clean, salt-free bare steel 10 – 12 mils || 250 – 300 microns DFT (Average ~ 100 sq. ft per US gallon ZERO LOSS FACTOR.)
TR2200HS HRCSA Penetrant
Apply liberally to crevices and joints &/or spaces where a gap has been created between plates, around rivets, bolts, nuts and washers, allowing the material to soak into the spaces. – NOT TO BE USED AS A PRIMER.
Coverage: Depending on structure, 10% TR2200HS per volume of TR2100 ordered. ie 10:1 ratio.
Click to download TR2200HS Penetrant Safety Data Sheets and Technical Data Sheets
TRT01 HRCSA thinner.
TRT01 Solvent is principally used for reactivating formerly applied HRCSA Primer/Topcoat, flushing paint lines back into original container and cleaning. The only time TRT01 Thinner is added to TR2100 HRCSA Primer/Topcoat is when the coating needs to be thinned when temperatures are cold making it to thick to pump. (Heating maybe a better alternative to lower the viscosity of the TR2100)
Click to download TRT01 HRCSA Thinner Safety Data Sheets.
Worthy note: When flushing paint lines with TRT01, conserve the TR2100 HRCSA Primer/Topcoat by pumping the coating back into it’s original container. Once coating is out of the lines continue pumping and add a ½ inch layer of flushing thinner on the top of the recovered coating material. Seal the container and store for future use. Properly stored TR2100 HRCSA Primer/Topcoat has no shelf life limits and can be used again and again. (If a skin develops on the surface of the stored coating remove it and coating can be used).